Loading ...
epithelial cellscausingcapsular shrinkage
aluminum chloride ... vasoconstrictioncausesgingival shrinkage
while aluminum chloride results in vasoconstrictioncausesgingival shrinkage
Excess cortisolcausesdendritic shrinkage
cement in a controlled manner(passive) caused bycounteract shrinkage
Do not wash silk fabric base layers in washing and drying machinemay causeshrinkage
the risk of shrinkage ... that very thingcontributesto shrinkage
In that case , moisture from the surface of the wood will dry out fast (causingshrinkage
Washing and drying with heatwill causeshrinkage
by curing or thermal shrinkage caused by cooling(passive) caused byshrinkage
water - machine washing ... likelyto causeshrinkage
Machine drying on any heatmay resultin shrinkage
by heat or thermal shrinkage caused by firing(passive) caused byshrinkage
that the combination of water , heat and agitation arecausesshrinkage
by heat or the difference in thermal shrinkage caused by firing(passive) caused byshrinkage
the loss of moisture from concrete(passive) is caused byShrinkage
temperature and moisture changes(passive) is caused byShrinkage
a moisture problem ( relative humidity of the air is drier than the moisture content of the woodcausesshrinkage
wet - heating processleadsto shrinkage
by moisture loss on heating(passive) caused byshrinkage
100 % a moisture problem ( relative humidity of the air is drier than the moisture content of the woodcausesshrinkage
the washing process itself(passive) is also caused byShrinkage
AVOID high heat from a dryer ( after washingmay causeshrinkage
by further solvent loss on curing or drying(passive) caused byshrinkage
the heat from the dryer ... likelyto causeshrinkage
The dryer processmay causeshrinkage
Hot water and machine dryingcan causeshrinkage
Washing or drying in high heatwill causeshrinkage
Avoid tumble drying if possiblecausesshrinkage
excessive hot temperature ... likelyto causeshrinkage
the water cement ratio of concrete(passive) is mostly influenced byshrinkage
Avoid tumble dryingcausesshrinkage
process conditions(passive) is also influenced byShrinkage
Dry cleaning , hot water , or heated dryingmay causeshrinkage
by internal moisture evaporation(passive) caused byshrinkage
The dried out wood from sun heatcan causeshrinkage
by moisture loss on warming(passive) caused byshrinkage
Heat drymay causeshrinkage
In my experience , both the machine washing and machine drying processescan causeshrinkage
The combination of heat , friction and pressurewill causeshrinkage
from encroachment of edgewaterresultingfrom encroachment of edgewater
in size reductions up to 2 %can resultin size reductions up to 2 %
the sheeting to buckle or distortto causethe sheeting to buckle or distort
expansion of soulcan causeexpansion of soul
to structural distortionsmay contributeto structural distortions
for easy on - and - offdesignedfor easy on - and - off
to the lack of crackscontributesto the lack of cracks
restricted movementcausesrestricted movement
to the lack of fracturesleadsto the lack of fractures
high internal stress and crackingcan causehigh internal stress and cracking
to undesirable build - up of stress or surface sink - marks , poor appearancecan leadto undesirable build - up of stress or surface sink - marks , poor appearance
internal stress that can result in defects and dimensional changes leading to decreased adhesioncausesinternal stress that can result in defects and dimensional changes leading to decreased adhesion
to shrinkage crackingcan leadto shrinkage cracking
cracking , curling , and excessive joint movement in a concrete slabcan causecracking , curling , and excessive joint movement in a concrete slab
to severe surface cracking and eventually loss of the coatingleadingto severe surface cracking and eventually loss of the coating
the formation of wide deep cracks and washing of surface materials into these crackscausesthe formation of wide deep cracks and washing of surface materials into these cracks
internal stress in the molded part and warpagemay also causeinternal stress in the molded part and warpage
the development of tensile stresses in concretecausesthe development of tensile stresses in concrete
to cracking , warping , and curling of the slableadingto cracking , warping , and curling of the slab
concrete crackscausesconcrete cracks
to cracking in concreteleadsto cracking in concrete
to the surface cracksmay leadto the surface cracks
micro cracks and permeability problemscausesmicro cracks and permeability problems
aesthetic , serviceability , and even stability issues with the onset of cracking , curling / warping , and reduced load - carrying capacitymay causeaesthetic , serviceability , and even stability issues with the onset of cracking , curling / warping , and reduced load - carrying capacity
cracking or adhesion problemscan causecracking or adhesion problems
excessive shrinkage or differential movements(passive) caused byexcessive shrinkage or differential movements
in increased wavelength from laser elementsto resultin increased wavelength from laser elements
A shrinkage crack(passive) is caused byA shrinkage crack
in the cracks formationresultsin the cracks formation
in cracking and movement due to the drying processcan resultin cracking and movement due to the drying process
Internal cracks(passive) are mostly caused byInternal cracks
curling/ warping which can lead to a variety of slab issues including decreased load - carrying capacity ( structural cracking ) and joint stability problems such as spallingalso causescurling/ warping which can lead to a variety of slab issues including decreased load - carrying capacity ( structural cracking ) and joint stability problems such as spalling
crack development and strength losscausescrack development and strength loss
by cracking timecausedby cracking time
to cracking or distortion inleadsto cracking or distortion in
in distortion or crackingmay resultin distortion or cracking
cracking and distortioncausescracking and distortion
to cracks or holes in visible areasgenerally leadingto cracks or holes in visible areas
Shrinkage Voids(passive) are caused byShrinkage Voids
to cracks , gaps , leakage or post - operative sensitivitymight leadto cracks , gaps , leakage or post - operative sensitivity