Loading ...
Page 196 Headlight adjustment Turn the screw ( 1to setbeam width
the base station(passive) set bythe beam width ,
the beam width setting unit(passive) set bya beam width
The magazine has adjustable lateral guidesto setthe beam width
to , for example , 2 degrees(passive) is setThe beam width
to be 20 for decoding(passive) is setBeam width
between 0.20 and 0.16(passive) is setBeam width
The three milliradian laser beam , as produced by the LTI 20/20 Marksmancreatesa beam width
to amply cover the tumor volume 20 and a margin of tissue around the tumor volume 20 sufficient to cover any elective treatment area(passive) is setThe beam width
to be sufficiently broad ( e.g. , half - power beam width equal to 50 degrees ) to suppress the frequency of closed - loop control and to make the power consumption in a motor low , as will be described later(passive) is designedThe beam width
to size(passive) is setThe Beam width
The aperture diaphragmsetsthe beam width
to ' narrow ' for maximum detection range when searching for fish at long distance(passive) can be setThe beam width
errorsresultingfrom beam width
A 3.5 mR laser beamwill createa beam width
to a predetermined width(passive) is setthe beam width
to a wide field of view on the general road(passive) is setThe beam width
to Float from Curve(passive) is setThe Beam Width
the gain medium(passive) is ... set byThe beam width
for each scanning which is made within 1μsec(passive) is setThe beam width
The dimension B should be set to the width of the design slab stripshould be setto the beam width
to give high uniformity on the road on single row installation when the road width is up to 2x the height of the installation(passive) is designedBeam width
at 240 degrees(passive) is setThe beam width
to 155 jm(passive) was setBeam width
multi - beam with an aperture much larger than the actual apertureresultingin beam - width
an the direction of infrared rays emitted from the laser 111(passive) are setThe beam width
each feedhorn(passive) created bythe beam width
to be very narrow or up to Lambertian with either the primary surfaces , or the addition of modifying surfaces(passive) can be designedThe beam width
larger numbers of ceramic elements , lower Q , increased depth performance , and increased target definitionwill ... resultbeam width
to 30(passive) is setThe beam width
so that the width of the fine crystal grain region 35 is approximately equal to that of each of the stripe regions 30A and 30B. Laser irradiation of the second shot(passive) is setThe beam width
Black hand ... 445 mm Width of wood : 69 mmpaintedCross beam width
the little dish on top of the piezo elementsetsthe beam width
to 3000(passive) is setThe beam width
diffraction(passive) is set byThe beam width
to maximize accuracy while still running faster than real - time(passive) was setThe beam width
the curvature of the mask 80 corresponds to at least the Talbot distance of the light - field generated by the periodic pattern in the mask 80(passive) caused bythe beam - width
our microphone array system(passive) created bybeam width
6 - 8 - 17 Text type BlackpaintedCross beam width
Turbulenceinfluencesthe beam width
cylindrical lens 3settingcylindrical lens 3
to the predetermined rangeis setto the predetermined range
but that ’s an optical illusion(passive) created bybut that ’s an optical illusion
to 1 in the conventional two minutesis setto 1 in the conventional two minutes
to be one $ B=1 $is setto be one $ B=1 $
to 440 μm on the welded surface at a frequency of 20 MHz so that a scattering type penetrator can be detectedsetto 440 μm on the welded surface at a frequency of 20 MHz so that a scattering type penetrator can be detected
cylindrical lens for setting the width of the laser beam in the direction which is perpendicular to the direction of advance of the laser beam and parallel with the reflecting surfaces of the multiple reflecting mirror unit , whereby , in shaping a laser beam , the energy loss of the laser beam is minimizedsettingcylindrical lens for setting the width of the laser beam in the direction which is perpendicular to the direction of advance of the laser beam and parallel with the reflecting surfaces of the multiple reflecting mirror unit , whereby , in shaping a laser beam , the energy loss of the laser beam is minimized
in improved beam separation and minimal loss of signal strengthresultsin improved beam separation and minimal loss of signal strength
too wideis settoo wide
to about 5 to 10 μmis setto about 5 to 10 μm
to a wider or narrower settingcan be setto a wider or narrower setting
to ~3.4 °is setto ~3.4 °
to an amount of less than 10 degrees ... with half of the degrees of the beam width allocated to either side of an angle designated to the steering directionis setto an amount of less than 10 degrees ... with half of the degrees of the beam width allocated to either side of an angle designated to the steering direction
at the will of manufacturersdesignedat the will of manufacturers
to 3 instead of 2were setto 3 instead of 2
from water - coolingresultingfrom water - cooling
a boat 's security , velocity , and ability to provide to an edgecan influencea boat 's security , velocity , and ability to provide to an edge
a ship 's my latest blog post steadiness , speed , and talentcan influencea ship 's my latest blog post steadiness , speed , and talent
the beam to deviate from a straight line path making aiming more difficultcausingthe beam to deviate from a straight line path making aiming more difficult
issuescan causeissues
from the refraction at the first surfaceresultingfrom the refraction at the first surface
to 100is setto 100
in a slight beam spreading as illustratedresultingin a slight beam spreading as illustrated
to “ narrow ” and there is a wall close to and directly behind the loudspeakeris setto “ narrow ” and there is a wall close to and directly behind the loudspeaker
a voluminous internal mission deck with a high payload carrying capacitycreatinga voluminous internal mission deck with a high payload carrying capacity
as constant for studies that do not vary the width of the substratecan be setas constant for studies that do not vary the width of the substrate
occurrence(passive) caused byoccurrence
a boat 's security , velocity , and talentcan influencea boat 's security , velocity , and talent
a ship 's security , velocity , and talentcan influencea ship 's security , velocity , and talent
large for indoor transmission by adopting diversity receptionis setlarge for indoor transmission by adopting diversity reception
into the productsdesignedinto the products
at 8'6is setat 8'6
fluctuations of energy intensity within the cross section of the beamcausingfluctuations of energy intensity within the cross section of the beam
to a large numberis setto a large number
to shankingcontributingto shanking
for inboardsDesignedfor inboards
to a small numberis setto a small number
nothing except weight and $ $contributesnothing except weight and $ $
powerinfluencespower
in negligible intra - cell interferenceresultsin negligible intra - cell interference